Arrow Dynamics Stinger Woodgrain Carbon ShaftsItem Number: 67871X
$87.50 $75.50
Made in the US
Arrow Dynamics Stinger Woodgrain Carbon Shafts

Arrow Dynamics Stinger Woodgrain Carbon Shafts

Item Number: 67871X
Loading
0
$87.50 $75.50
Made in the US


In Stock

Add To Wishlist

Featuring a traditional Woodgrain finish!

Arrow Dynamics Stinger is a parallel-to-taper carbon shaft that utilizes conventional components. The tapered shaft creates better fletching clearance allowing for a quicker recovery from the paradox and translating more of the bow's kinetic energy to the arrow. This unique taper allows for more EFOC (Extreme Front of Center) weight without having to add weight tubes or heavyweight points. With EFOC you will see better penetration on big game, and tighter groups with pin-point accuracy. A full length bare shaft with a 145 grain point generates more than 20% EFOC

The 100% carbon shaft is a .246" inside diameter at the point end for the first 13" and tapers to a .165" ID at the nock end. Includes 17 grain aluminum inserts and white Bohning 'F' nocks.

Point end works with all .246" components (such as 5/16" brass inserts) and the nock end works with Easton G nocks or Bohning F nocks. Sold by the 6-pack and 12-pack. Made in the USA.

  • .246" inside diameter for the first 13", then tapers to .165"
  • Made in USA
  • ±.003 straightness
  • Built in EFOC weight (extreme front of center)
  • Works with most popular 5/16" components
  • Good arrow flight through a wide range of bow weights with same spine arrow
  • Quick recovery due to parallel to taper design
  • Woodgrain Finish

Arrow Dynamics Stinger Carbon Shafting Specifics
Spine Point GPI Length Insert Nock Point
Collar
Nock
Collar
500 5/16" No GPI due to taper design
Roughly 310gr @ 32"
32 ¼" 17gr Bohning F Nock E --
400 5/16" No GPI due to taper design
Roughly 330gr @ 32"
32 ¼" 17gr Bohning F Nock C --
330 5/16" No GPI due to taper design
Roughly 358gr @ 32"
32 ¼" 17gr Bohning F Nock N --
Straightness      ±.003"        Weight    N/A

PLEASE NOTE: Any service requested may delay shipment. Items with services applied are non-refundable.

Services Available
Standard Fletch: Our experienced fletchers will 3-fletch your carbon shafting with 5" shield left wing TrueFlight feathers. The cock feather will be traditional barred and the 2 hen feathers will be your choice of white, yellow, red, or fluorescent lime (same color for all arrows). Hen feather color can be requested and will be fletched on a CLEAR cap wrap. No substitutions. Allow 4-7 additional business days for your order to be processed.

Cut Shafts to Length:  Have your carbon shafts cut to length. The length is measured from the throat of the nock to the back of the point. Minimum length is 27½".

Install Inserts:  Choose this option to have our experts install your Aluminum Point Inserts in your shafts. Please Note: If you select this service without selecting the "Cut to Length" service, your shafts will be cut to the stock length (as specified in the chart above). Please Note: We use epoxy style adhesives on all inserts and most points. Once they are installed, they are permanent.

Not sure which size to order? See Printable Shaft Selection Chart PDF


Additional Components
3Rivers Glue-In Target Points
SKU: 715-1
3R Glue-In Target Points
Brass Glue-In Broadhead Adapters
SKU: 4930X
Brass Glue-In BH Adapters - 5/16"
Easton Glue-In Target Points
SKU: 6793X
Easton CB Glue-In Target Points
Insert Weights
SKU: 6696X - Gold Tip Insert Weights - .246"
SKU: 681205X - Black Eagle Insert Weights
Brass Inserts
SKU: 0255X - Brass Inserts - 5/16"
SKU: 6692-04X - Gold Tip Brass Inserts
Bohning Blazer F Nock
SKU: 0170X
Bohning Blazer F Nock®
Easton G Push-In Nocks
SKU: 6754X
Easton G Push-In Nocks

Warning: Cancer and Reproductive Harm
www.P65Warnings.ca.gov