Visitor Monitoring
blank
blank

DAS ILF LIMB FITTING


Some fitting is required to convert ILF limbs for use on the DAS bow. Follow the instructions carefully and you will have no trouble.

    1. The first step is to remove the ILF dovetail fitting. Remove the screw from the top of the fitting. Remove the spring and plunger inside the fitting. Drill a 9/16" hole in a piece of scrap wood. Place the limb on the wood with the fitting over the hole. Now use a plastic or rawhide mallet to carefully tap the fitting down and out. You will need a length of some soft material like hardwood, brass, or aluminum to drive the fitting all the way out. A better way to do this is to use an arbor press.

    2. The bushings required to adapt the limbs are sized to be a push in fit on Hoyt and Sky limbs. No sizing to the hole is required. For Korean limbs like W&W, Samick, etc., the hole must be slightly enlarged from .358 to .372. You can do this by using a .372 reamer, or a piece of sandpaper wrapped around a dowel. DO NOT USE A 3/8 DRILL!! The fit should be very snug, not loose. Go slow, be careful!

    3. Clean any dust out of the limb hole and wipe in a thin film of 5 minute epoxy.

    4. Press or tap in the insert using the wood block with the hole underneath to support the limb. Wipe off any excess epoxy and let it cure.

    5. To remove a DAS insert, thread a ¼-20 X 2" bolt into the insert till it bottoms. Place the limb over the wood block as you did to remove the ILF dovetail. Press or tap the insert out. The epoxy does not have too tight a grip so it will let go. NEVER HIT OR PRESS DIRECTLY ON THE INSERT!! IT WILL MUSHROOM AND BE A BEAR TO GET OUT!

    6. Next step is to measure the depth of the slot in the limb. The depth should be .400 inches to .420". If the slot is longer it may contact the riser when installed and result in excess noise. The best way to measure the slot is with the tail end of a dial caliper. To reduce the depth of the slot, use a sanding block and take down the end of the limb until the slot is the right depth. Don't go too far, the stuff sands pretty easy.

    7. The last step is to check the fit of the slot over the brass sleeve on the bow. Most limbs are a hair tight. Use the sandpaper (about 100 grit works good on an 11/32 arrow) and CAREFULLY enlarge the slot till the limb just slips on. It can be a bit snug, but sloppy is not good. Make sure the limb goes all the way down on the brass sleeve.

    8. To reseal the areas you just sanded, you can use a thin wipe of epoxy, superglue, or clear fingernail polish.

    9. The limb is now ready to use.

blank
McAfee SECURE sites help keep you safe from identity theft, credit card fraud, spyware, spam, viruses and online scams Click to verify BBB accreditation and to see a BBB report Trust Us Facebook page for 3Rivers Archery YouTube videos for 3Rivers Archery Google+ page for 3Rivers Archery
 
blank
 
 Customer Service    About Us    Product Details    Extra Features    Top Categories
 866-732-8783
 Info@3RiversArchery.com

 My Account 
 Check Order Status 
 Shipping Information 
 Return Policy 
 Privacy Statement 
blank
 3Rivers Archery
 PO Box 517
 607 HL Thompson Jr Dr
 Ashley, IN 46705

 Request a Catalog 
 Learn More About Us 
blank
 Top Searches 
 Gift Certificates 
 Dealer Information 
blank
 Email Sign Up 
 Trophy Room 
 3D Shoots 
 Arrow Whiz 
 Military Discount 
Read Our Blog
blank
 Kid bow sets 
 Recurve bows 
 Longbow bows 
 Carbon arrows 
 Wood arrows 
 Broadheads 
 Youth Archery 
blank
©2014 Three Rivers Archery Supply, Inc. All Rights Reserved.
No part of this web site may be copied or reproduced without the express written permission of Three Rivers Archery Supply, Inc.
3RiversArchery.com
Ask The Experts info@3riversarchery.com Ask the Experts at 3Rivers Archery
Search
Blank space
Order Status Gift Cards Free Catalog Customer Service Sale Items 3Rivers Archery Customer Service and Sale Items
Sign In 3Rivers Archery Welcome and Sign In
($0.00 / 0 items) View Cart at 3Rivers Archery
Background Blank
100% Satisfaction Guarantee 3Rivers Archery 100% Satisfaction Guaranteed
Leading the industry. EXPERIENCE (over 250 years.) KNOWLEDGE (experts at being THE EXPERTS.) AMERICAN PRODUCT SELECTION (over 90% of products Made in the USA.)